
Test Engineer
PEAK Technical Services · Leetsdale, PA
Strong hiring record · median 15 days open
- First seen
- 20 November 2026
- Reposted
- Not since September 2026
All reasons
In its favour
- Posted today
- Still listed on the employer's own board
The Test Engineer I position is a hands on position that performs high level testing and provides engineering input for current and new products and customer/application specific projects.
Duties and Responsibilities
- Performs various laboratory assignments primarily involving hydraulic test stands but also including electrical applications, electronics, instrumentation, and calibrations.
- Develops testing procedures to replicate real world applications within the Fluid Care Center.
- Maintains a strong understanding of product testing and product performance specifications, this individual provides value-added input such as observations and feedback during new and existing product testing, working closely with Engineering.
- May assist in the development of new products for commercial launch, from concept through design, testing, and introduction. Supports new products after commercial introduction. Evaluates, improves, and certifies for production any new products. Such efforts would include, but are not limited to, the creation and/or design review of the following documents; SOP (Standard Operating Procedures), assembly drawings, element construction drawings, detail machining drawings, BOM's (Bill of Material), assembly drawings, technical manuals, etc.
- Provides engineering support for the design of new products or the modification of established products in response to company or customer requirements within the guidelines of the Company policy, cost effectiveness, manufacturability, product safety and liability, accepted engineering practices, applicable standards or regulations, and within the time constraints established by the FCC Supervisor.
- Assists in the design of new tooling, fixtures, test equipment and prototype components as necessary.
- Conducts and runs various tests associated with fluid analysis, including particle counting, viscosity measurement, Karl Fischer Titration, patch testing & microscopic analysis.
- Understands, and is able to conduct multi-pass testing per ISO 16889.
- Performs or assists in client tours/training/troubleshooting within the lab or at a client's facility.
- Performs other duties as assigned.
Qualifications
To perform this job successfully, an individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill and/or ability required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.
Qualifications
- Minimum of Bachelor's Degree in Engineering is required; BSME, BSIE, BSc or BSEE is required.
- Knowledge of AutoCAD and/or Solid Works or equivalent computer aided drafting system is required.
- Experience in fluid power industry and/or manufacturing environment is preferred.
Skills and Abilities
- Knowledge of product design, project management, and hydraulic/electrical schematics as applied to fluid power is preferred.
- To perform this job successfully, an individual should have excellent knowledge of ERP software, spreadsheet software and word processing software; SAP experience is a plus.
- Has an understanding of, or willingness to learn data acquisition software and systems (LabView or similar) and is able to use the software with existing test equipment.
Certificates and Licenses
- Fluid Power Specialist Certification is required within eighteen months of employment.
Other Requirements
- Travel, including driving, is required, including occasional travel to domestic and international locations.
Working Environment
Manufacturing facility. The noise level can be loud, at times requiring hearing protection.
Physical Requirements
Physical Abilities Lift / Carry
Stand F 10 lbs or less O
Walk F 11-20 lbs O
Sit F 21-50 lbs O
Handling / Fingering C 51-100 lbs O
Reach Outward C Over 100 lbs N
Reach Above Shoulder F Push / Pull
Climb O 12 lbs or less O
Crawl O 13-25 lbs O
Squat or Kneel O 26-40 lbs O
Bend O 41-100 lbs O
N (Not Applicable) Activity is not applicable to this occupation.
O (Occasionally) Occupation requires this activity up to 33% of the time (0 - 2.5+ hrs/day)
F (Frequently) Occupation requires this activity from 33% - 66% of the time (2.5 - 5.5+ hrs/day)
C (Constantly) Occupation requires this activity more than 66% of the time (5.5+ hrs/day)
Safety and Personal Protective Equipment
Must adhere to all safety rules in force for the location you are in while performing your job responsibilities. This includes at a customer or supplier location. Must meet requirements for PPE in specific manufacturing areas when you are in those areas including safety shoes and safety glasses.
Direct Reports
Not applicable.
The company has reviewed this job description to ensure that essential funct
More jobs at PEAK Technical Services
All 25- Field Service TechnicianPEAK Technical Services · Saint Paul, MN · USD 25–30/hrtoday
- Product ManagerPEAK Technical Services · Pittsburgh, PAyesterday
- Electronics Test EngineerPEAK Technical Services · Camarillo, CA · USD 95,000–120,000/yr3d ago
- PLC ProgrammerPEAK Technical Services · Bridgeville, PA3d ago
- Senior Salesforce DeveloperPEAK Technical Services · Washington, DC4d ago
Similar roles
- Quality Test Engineer - St. Louis, MO (100% Onsite or Weekly Travel Required)Accenture Federal Services · St. Louis, MOtoday
- Test EngineerIcarus · El Segundo · USD 100,000–140,000/yrtoday
- Test EngineerArtech · Foster City, CAtoday
- Test EngineereTeam · Longmont, COtoday
- Flight Test EngineerIcarus · El Segundo · USD 125,000–185,000/yrtoday
- Test Engineer 3_USDArtech · Longmont, COtoday